Product Center
Home » gas cutting machine hazards and protection
  • Gas Safety Device and Cutting Machine - Portable Gas ...

    Wholesale Trader of Gas Safety Device and Cutting Machine - Portable Gas Cutting Machine, Boris Flashback Arrestor, Retractable Fall Arrest Systems offered by Affelotus Engineers, Nashik, Maharashtra.

  • Welding Safety Tips and Guidelines - Quick Tips #109 ...

    Dec 01, 2018 · Oxygen cutting: Metal is heated by gas flame, and an oxygen jet does the cutting Arc cutting: Intense heat of electric arc melts away the metal. Personal Protective Equipment (PPE) Eye and face protection: 29 CFR 1910.252(b)(2) states the requirements for eye protection. . Helmet, handshield, goggles and safety glasses or combination of these ...

  • Laser Cutter Safety - EHS

    Safety. Laser cutters must be obtained from a reputable suppliers and must be in full compliance with the FDA regulations. TRAINING AND PPE All users must be properly trained on the potential hazards, control measures, lab and manufacturer’s operating procedures, use of personal protective equipment (PPE), emergency procedures, and safety

  • SAFETY IN GAS CUTTING AND WELDING | RLS HUMAN CARE

    Oct 20, 2017 · Open the DA regulator, the torch valve and light the gas. Then open the oxygen valves to the required pressure. After cutting start closing from oxygen and then DA. HAZARDS IN GAS CUTTING:-–FLASHBACK. –BACKFIRE. –GENERAL FIRE. –EXPLOSION. A FIRE ON CYLINDER:-try to put out the fire. close the valve if it gets put out.

  • Welding, burning, & cutting - Environmental Health and Safety

    acetylene, or any other fuel or gas is present. Determine the cause of the leak and get it corrected. 2. Do not perform any “hot work” (electric or gas welding, cutting, and brazing or similar flame-producing operations and grinding) in, or on, a tank or container unless it is properly vented. 3.

  • Physical Hazards of Machinery and Equipment

    2 CONTINUED: Physical Hazards of Machinery and Equipment Shear Points – Any point where sharp edges of two moving parts move across one another, or where a single sharp part moves with enough speed or force to cut soft material. ⎯ Cutting devices cannot be completely guarded to keep hands and feet out and still perform their intended function.

  • Safety in gas welding, cutting and similar processes

    Health and Safety Executive Safety in gas welding, cutting and similar processes This leaflet is for people who use compressed gases for welding, hot cutting and similar processes. It describes the hazards associated with portable oxy/fuel gas equipment and the precautions for avoiding injury and damage to property. Introduction

  • Oxy-fuel welding and cutting - Wikipedia

    Oxy-fuel welding (commonly called oxyacetylene welding, oxy welding, or gas welding in the United States) and oxy-fuel cutting are processes that use fuel gases (or liquid fuels such as gasoline) and oxygen to weld or cut metals. French engineers Edmond Fouché and Charles Picard became the first to develop oxygen-acetylene welding in 1903.Pure oxygen, instead of air, is used to increase the ...

  • Cut-off Machine Safety Manual - STIHL USA

    The use of any cut-off machine may be hazard-ous. Because a cut-off machine is a high-speed, fast-cutting power tool, special safety precau-tions must be observed to reduce the risk of per-sonal injury and fire. It is important that you read, fully understand and observe the following safety precautions and warnings. Read the instruction manual and

  • Safety Risk Assessment in CNC GAS Cutting Machine of ...

    Abstract— The aim of this risk assessment is highlighting the safety aspect in CNC gas cutting process.The gas cutting is one of the hazardous process in manufacturing industry which have multiple potential hazard so that we have applied risk assess-ment method to find out risk related to it and also given coun-termeasures to reduce or eliminate risk in order to make the working environmental safe …

  • Safety and Health Policy and Procedure Manual WELDING ...

    1910.252 Welding, Cutting, and Brazing 1926.350 Gas, Welding, and Cutting IV. GENERAL REQUIREMENTS A. Basic Precautions for Fire Prevention 1. The object to be welded should be moved to a safe place, when possible. 2. If the object cannot be readily moved, all movable fire hazards in the vicinity shall be moved to a safe location. 3. If the ...

  • EHS 320 Welding Cutting and Brazing - ehso.emory.edu

    • Use goggles or other suitable eye protection during all gas welding or oxygen cutting operations. Spectacles without side shields but with suitable filter lenses are permitted for use during gas welding operations on light work, for torch brazing or for inspection. • All operators and attendants of resistance welding or resistance brazing

  • Welding and Cutting Personal Protective Equipment | Office ...

    16 rows · Welding and Cutting Personal Protective Equipment. ‹ Hot Work Procedures up Handling …

  • Grinder Safety -Hazards, Precautions, PPE - Safety Notes

    Aug 10, 2019 · Grinder Machine Hazards All types of grinding machines, whether pedestal, bench mounted, free-standing or portable, can be potentially hazardous if they are not well maintained and used correctly. In addition to the common hazards of flying particles, dust and sparks, shattering abrasive wheel while in Motion can cause severe injury to both the ...

  • The many hazards of welding work | 2020-01-26 | Safety ...

    Jan 26, 2020 · Key points More than one-third (140) of the 370 lost-time injuries reported by the Bureau of Labor Statistics in 2018 were the result of thermal or heat burns. The National Fire Protection Association 51B standard covers fire prevention for welding and other hot work, and is used for part of OSHA 1910 Subpart Q. Electrical, ergonomic, mechanical and work environment hazards are among …

  • The Mechanical Machinery Hazards | Mechanical Safety

    Mar 21, 2018 · Mechanical Machinery Hazards. Most machinery has the potential to cause injury to people, and machinery accidents figure prominently in official accident statistics. These injuries may range in severity from a minor cut or bruise, through various degrees of wounding and disabling mutilation, to crushing, decapitation or another fatal injury.

  • POTENTIAL HEALTH & SAFETY HAZARDS - TRU

    The following operations require full face protection from either a welding helmet or a hand shield: •arc welding, •plasma arc cutting, gouging or welding, and •air carbon arc cutting. For gas cutting, welding, or brazing, the intensity of the light is much less than from arc welding, Page 7 of 21

  • Welding, Cutting, and Brazing Checklist

    Welding, Cutting, and Brazing Checklist for General Industry (A negative answer to any question indicates an area of safety or health concern.) Company name: Physical address of worksite: Supervisor: Date/Time: Inspector: General Industry – CFR 1910 . Installation and Operation of Oxygen-Fuel Gas Systems for Welding and Cutting – 1910.253

  • OSHA shines spotlight on metal fabricating

    Feb 10, 2015 · Eye and face protection. Metal fabricators typically need eye and face protection from flying particles, molten metal, liquid chemicals, chemical gases or vapors, harmful light radiation, and infectious materials. Full face shields may also be needed to protect their face from these hazards. Hand protection.

  • Plasma Arc Cutting Hazards -- Occupational Health & Safety

    Mar 01, 2003 · Plasma Arc Cutting Hazards. Mar 01, 2003. THIS is the fourth in the series of articles on welding safety. The central theme of these articles has been to …

  • The 10 Trenching Safety Tips That Can Save a Life | BigRentz

    Dec 26, 2019 · Take a look at these essential trenching safety tips that your team should follow: 1. Install Protective Systems. Protective systems keep workers safe from cave-ins and deaths, in fact, preventing injury and death from cave-ins is one of OSHA’s primary goals. A protective must be put into place if the trench is deeper than 5 feet; if the ...

  • Gas Welding & Cutting - Construction Hazards & Safety

    Any individual engaged in welding and cutting must demonstrate compliance with these provisions. 1926.350(a) Transporting, moving, and storing compressed gas cylinders. 1926.350(a)(1) Valve protection caps shall be in place and secured. 1926.350(a)(2) When cylinders are hoisted, they shall be secured on a cradle, slingboard, or pallet.

  • Welding Safety Hazards and Precautions - Health and Safety ...

    Oct 01, 2009 · Each of these aspects has implication on the health and safety of the welder. Gas welding is rarely used in production now, but oxy-fuel gas processes are still prevalent for cutting. These rely on melting and expelling metal from the plate so protection is required both to observe progress and to avoid being burnt by flying metallic particles.

  • Laser Cutting Machine Safety Guide

    Laser Cutting Machine Safety Guide (For employers and employees) FourthA edition April 2018 ... protection of employees from laser hazards. 3 (3) Implementation of safety and health education ... gas cutting. Laser cutting is a machining process that forcibly removes the material by using the reaction of

  • Plasma Cutting Safety – Welding Protective Equipment

    Dec 12, 2019 · During the cutting process fumes and gasses are produced. Especially, if you work with coated metals, they produce toxic fumes. These fumes and gases are extremely hazardous. They may cause fatal health hazards to the operator and even to the working environment and other workers.

  • Gas cutting and Gas Welding Hazards - Welding Guide

    Feb 07, 2014 · Gas cutting and welding involves direct exposure to molten material, sparks and heat, apart from while repairing drums/tanks, with inflammable liquids; you are exposed to grievous injuries, if you do not take precautions. Most of the fire hazards, fumes from flames, leakage of gas are the result of misuse of fire or oxygen.

  • Safety in Welding, Cutting, and Allied Processes

    Safety in Welding and Cutting Secretariat American Welding Society Abstract This standard covers all aspects of safety and health in the welding environment, emphasizing oxygen gas and arc welding processes with some coverage given to resistance welding. It contains information on protection …

  • Laser Cutting Machine Safety Guide

    (4) Hazards of laser cutting machines Hazards of toxic gases to human body When polyvinyl chloride is laser cut, it releases toxic hydrogen chloride gas. This toxic gas powerfully corrodes equipment. Do not laser cut polyvinyl chloride. The laser cutting of nylon and polyurethane generates toxic hydrogen cyanide gas. Do not laser cut them.